amphenol代理商
专业销售Amphenol（安费诺）全系列产品-英国2号仓库
库存查询
美国1号分类选型新加坡2号分类选型英国10号分类选型英国2号分类选型日本5号分类选型

在本站结果里搜索：    
热门搜索词:  Connectors  8910DPA43V02  Amphenol  UVZSeries 160VDC  70084122  IM21-14-CDTRI

FLUKE-435-II - 

Power Analyzer; 1000 Vrms; 30-3000Arms; 50KOhms; >10KHz; 435 II Series; Handheld; IP51

Fluke FLUKE-435-II
声明：图片仅供参考，请以实物为准！
制造商：
Fluke Fluke
制造商产品编号：
FLUKE-435-II
仓库库存编号：
70227764
技术数据表：
View FLUKE-435-II Datasheet Datasheet
订购热线： 400-900-3095  0755-21000796, QQ:800152669, Email:sales@szcwdz.com
由于产品数据库庞大，部分产品信息可能未能及时更新，下单前请与销售人员确认好实时在库数量，谢谢合作！

FLUKE-435-II产品概述

Fluke 435-II Three-Phase Power Quality and Energy Analyzer

Features:
  • Troubleshoot real-time: Analyze the trends using the cursors and zoom tools.
  • Highest safety rating in the industry: 600 V CAT IV/1000 V CAT III rated for use at the service entrance.
  • Power inverter efficiency: Simultaneously measure AC output power and DC input power for power electronics systems using optional DC clamp.
  • PowerWave data capture: 435 and 437 Series II analyzers capture fast RMS data, show half-cycle and waveforms to characterize electrical system dynamics (generator start-ups, UPS switching etc.).
  • Waveform capture: 435 and 437 Series II models capture 100/120 cycles (50/60Hz) of each event that is detected in all modes, without set-up.
  • Automatic Transient Mode: 435 and 437 Series II analyzers capture 200 kHz waveform data on all phases simultaneously up to 6 kV.
  • Energy loss calculator: Classic active and reactive power measurements, unbalance and harmonic power, are quantified to pinpoint true system energy losses in dollars (other local currencies available).
  • Fully Class-A compliant: 435 and 437 Series II analyzers conduct tests according to the stringent international IEC 61000-4-30 Class-A standard.
  • 400 Hz measurement: 437 Series II analyzer captures power quality measurements for avionic and military power systems.
  • Measure all three phases and neutral: With included four flexible current probes with enhanced thin flex designed to fit into the tightest places.
  • Automatic Trending: Every measurement is always automatically recorded, without any set-up.
  • System-Monitor: Ten power quality parameters on one screen according to EN50160 power quality standard.
  • Logger function: Configure for any test condition with memory for up to 600 parameters at user defined intervals.
  • View graphs and generate reports: With included analysis software.
  • Battery life: Seven hours operating time per charge on Li-ion battery pack.
  • Mains signaling: 435 and 437 Series II analyzers measure interference from ripple control signals at specific frequencies.


    435 Series II Power Quality and Energy Analyzer
    Think of the Fluke 435 Series II Power Quality and Energy Analyzer as your insurance policy. No matter what goes wrong in your facility, with the 435 II you will always be prepared. Equipped with advanced power quality functions and energy monetization capabilities, there is no electrical issue this model can’t handle.

    PowerWave function captures fast RMS values and allows you to see every waveform to determine how the voltage, current and frequency values are interacting.
    Power Inverter Efficiency function measures both ac power and dc power, in and out, to monitor the efficiency of your inverters.
    And, as with the other 430 Series II models, the 435 II features an Energy Loss Calculator that will monetize energy waste due to poor power quality, helping you save on the energy bill.
    More detailed power quality analysis capability, and a new Fluke-patented energy monetization function

    The new 430 Series II Power Quality and Energy Analyzers offer the best in power quality analysis and introduce, for the first time ever, the ability to monetarily quantify energy losses.

    The new Fluke 434, 435 and 437 Series II models help locate, predict, prevent, and trouble-shoot power quality problems in three-phase and single-phase power distribution systems. Additionally, the Fluke-patented energy loss algorithm, Unified Power Measurement, measures and quantifies energy losses due to harmonics and unbalance issues, allowing the user to pinpoint the origin of energy waste within a system.

    Unified Power Measurement
    Fluke’s patented Unified Power Measurement sys-tem (UPM) provides the most comprehensive view of power available, measuring:

    Parameters of Classical Power (Steinmetz 1897) and IEEE 1459-2000 Power
    Detailed Loss Analysis
    Unbalance Analysis
    These UPM calculations are used to quantify the fiscal cost of energy loss caused by power quality issues. The calculations are computed, along with other facility-specific information, by an Energy Loss Calculator that ultimately determines how much money a facility loses due to wasted energy.

    Energy savings
    Traditionally energy savings are achieved by monitoring and targeting, or in other words, by finding the major loads in a facility and optimizing their operation. The cost of power quality could only be quantified in terms of downtime caused by lost production and damage to electrical equipment. The Unified Power Measurement(UPM) method now goes beyond this to achieve energy savings by discovering the energy waste caused by power quality issues. Using the Unified Power Measurement, Fluke’s Energy Loss Calculator (see screen shot below) will determine how much money a facility is losing due to waste energy.

    Unbalance
    UPM gives a more comprehensive breakdown of the energy consumed in the plant. In addition to measuring reactive power (caused by poor power factor), UPM also measures the energy waste caused by unbalance; the effect of unevenly loading each phase in three-phase systems. Unbalance can often be corrected by reconnecting loads on different phases to ensure the current drawn on each phase is as equal as possible. Unbalance can also be corrected by installing an unbalance reactance device (or filter), that will minimize the effects. Correcting unbalance should be basic good housekeeping in the facility as unbalance problems can cause motor failure or shorten equipment life expectancy. Unbalance also wastes energy. Using UPM can minimize or eliminate that energy waste, thus saving money.

    Harmonics
    UPM also provides details of the energy wasted in your facility due to the presence of harmonics. Harmonics may be present in your facility due to the loads you operate or may be caused by loads in adjacent facilities. The presence of harmonics in your facility can lead to:
    Overheating transformers and conductors
    Nuisance tripping of circuit breakers
    Early failures of electrical equipment
    Quantifying the cost of wasted energy due to the presence of harmonics simplifies the return-on investment calculation needed to justify purchasing harmonic filters. By installing a harmonic filter the ill effects of harmonics can be reduced and energy waste eliminated, resulting in lower operationa

    • FLUKE-435-II产品信息

      Brand/Series  435 Series II  
      Configuration  Handheld  
      True RMS Current  5 A to 6000 A  
      True RMS Voltage  1 V to 1000 V  
      Type  Power Analyzer  
    关键词         

    FLUKE-435-II产品配件

    • 参考图片
    • 制造商 / 说明 / 型号 / 仓库库存编号
    • PDF
    • 操作
    参考价格及参考库存
      美国2号仓库    仓库直销，订单金额100元起订，满300元含运，满500元含税运，有单就有优惠，量大更优惠，支持原厂订货
    型号 制造商 描述 操作
    FLUKE-435-II
    [更多]    		 Fluke Corporation

    Power Analyzers PwrAnalyzer w/Logger 1000Vrms Three-Phase

    RoHS: Compliant

    		搜索
    FLUKE-435-II/BASIC
    [更多]    		 Fluke Corporation

    Power Analyzers PwrAnalyzer w/Logger 1000Vrms Three-Phase

    RoHS: Compliant

    		搜索
      美国4号仓库    仓库直销，订单金额100元起订，满300元含运，满500元含税运，有单就有优惠，量大更优惠，支持原厂订货
    型号 制造商 描述 操作
    FLUKE-435-II
    [更多]    		 Fluke Corporation  

    		搜索
      新加坡2号仓库    仓库直销，订单金额100元起订，满300元含运，满500元含税运，有单就有优惠，量大更优惠，支持原厂订货
    型号 制造商 描述 操作
    FLUKE 435-II
    [更多]    		 Fluke Corporation

    ANALYSER, ENERGY, HARMONICS, POWER, 8 CH

    		搜索
      英国2号仓库    仓库直销，订单金额100元起订，满300元含运，满500元含税运，有单就有优惠，量大更优惠，支持原厂订货
    型号 制造商 描述 操作
    FLUKE-435-II
    [更多]    		 Fluke Calibration

    Power Analyzer, 1000 Vrms, 30-3000Arms, 50KOhms, >10KHz, 435 II Series, Handheld, IP51

    RoHS: Not Compliant

    		搜索
    查看资料
    FLUKE-435-II/BASIC
    [更多]    		 Fluke Calibration

    Power Analyzer, 1000 Vrms, 30-3000Arms, 50KOhms, >10KHz, Handheld, IP51 With out

    RoHS: Not Compliant

    		搜索
    查看资料
    FLUKE-435-II-OPENED
    [更多]    		 Fluke Calibration

    Power Analyzer, 1000Vrms, 30-3000Arms, 50KOhms,

    RoHS: Not Compliant

    		搜索
    查看资料
    FLUKE-435-II/OPEN BOX
    [更多]    		 Fluke Calibration

    Power Analyzer, 1000 Vrms, 30-3000Arms, 50KOhms, >10KHz, 435 II Series, Handhel

    RoHS: Not Compliant

    		搜索
    查看资料
      日本5号仓库    仓库直销，订单金额100元起订，满300元含运，满500元含税运，有单就有优惠，量大更优惠，支持原厂订货
    型号 制造商 描述 操作
    FLUKE 435-II
    [更多]    		 Fluke Calibration

    Power Quality Analyzer Dimensions L x W x H: 265 x 190 x 70 mm Weight: 2 kg Application: Three-Phase Bandwidth: 50 Hz/60 Hz Basic accuracy, current, AC/DC: ±0.5 % Basic accuracy, power, energy: ±1 % Basic accuracy, voltage, AC/DC: ±0.1 % Delivery with: Current Clamp x 4 / Software Display: 6" / LCD Electrical supply: Li-ion battery / Mains power battery charger Inputs: 4 voltage and 4 current inputs (for 3 phases and neutral conductor) Interfaces: SD-Card / USB / USB Mini-B Measuring function: A / CF / COS ф / Data logger / Flicker / Hz / Inrush / PF / Recorder function / THD / V / VA / VAh / VAr / VArh / W / Wh Protection rating: IP51 Safety to EN61010: CAT IV 600 V / CAT III 1000 V Type of measurement: TRMS AC + DC AAC max.: 6000 AAC AAC resolution: 100 mA Memory: 8 GB VAC max.: 1000 VAC VAC resolution: 0.01 V W max.: 6000000 kW W resolution: 0.1 W

    		搜索
    查看资料
      英国10仓库    查看更多相关产品
    产品描述 / 参考图片 制造商零件编号 / 制造商 / 库存编号 操作

    Fluke - FLUKE 435-II - Fluke 435 电能质量分析仪, 最大测量6000A ac, 6000W, LCD显示, RS232，USB接口
    		制造商零件编号：
    FLUKE 435-II
    品牌：
    Fluke
    库存编号：
    752-5008
    		搜索
      www.szcwdz.com    查看更多相关产品
    参考图片 型号/品牌 描述 / 技术参考 操作
    无图FLUKE 435-II
    FLUKE    		ANALYSER, ENERGY, HARMONICS, POWER, 8 CH; Analyzer Functions:Energy, Harmonics, Power; No. of Channels:8; Voltage Range rms:1V to 1kV; Bandwidth:100kHz; External Height:256mm; External Width:169mm; External Depth:64mm; SVHC:No SVHC (15-Jun-2015)
    暂无PDF     		查价格库存
    查看详细
    FLUKE-435-II|FLUKEFLUKE-435-II
    FLUKE    		分析仪 高性能 电能质量与能量 英式+欧式插头
    暂无PDF     		查价格库存
    查看详细
    无图FLUKE-435-II CAL
    FLUKE    		原厂原装货
    暂无PDF     		查价格库存
    查看详细
    无图FLUKE-435-II CAL D
    FLUKE    		原厂原装货
    暂无PDF     		查价格库存
    查看详细
      英国2号仓库    查看更多相关产品
    参考图片 制造商 / 说明 / 型号 / 仓库库存编号 PDF 操作

    Fluke - FLUKE-435-II - IP51 Handheld 435 II Series >10KHz 50KOhms 30-3000Arms 1000 Vrms Power Analyzer|70227764 | ChuangWei Electronics    		Fluke
    Power Analyzer; 1000 Vrms; 30-3000Arms; 50KOhms; >10KHz; 435 II Series; Handheld; IP51

    型号：FLUKE-435-II
    仓库库存编号：70227764

    		搜索
      www.szcwdz.cn    查看更多相关产品
    参考图片 型号/品牌 描述 / 技术参考 操作
    FLUKE-435-II|FLUKEFLUKE-435-II
    FLUKE    		分析仪 高性能 电能质量与能量 英式+欧式插头
    暂无PDF     		查价格库存
    查看详细
      日本5号仓库    查看更多相关产品
    参考图片 制造商 / 说明 / 型号 / 仓库库存编号 PDF 操作

    Fluke - FLUKE 435-II - Power Quality Analyzer 1000 VAC 6000 AAC, FLUKE 435-II, Fluke    		Fluke
    Power Quality Analyzer 1000 VAC 6000 AAC, FLUKE 435-II, Fluke

    型号：FLUKE 435-II
    仓库库存编号：176-43-095

    		搜索
    电话:400-900-3095
    QQ:800152669
    关于我们 | Amphenol简介 | Amphenol产品 | Amphenol产品应用 | Amphenol动态 | 按系列选型 | 按产品规格选型 | Amphenol选型手册 | 付款方式 | 联系我们
    Copyright © 2017 www.amphenol-connect.com All Rights Reserved. 技术支持：电子元器件 ICP备案证书号:粤ICP备11103613号
    深圳市市场监督管理局企业主体身份公示